Drone Tutorials and Help Videos from Cyclone FPV

HGLRC Forward F7 Dual Gyro FC Installation Notes

HGLRC Forward F7 Dual Gyro FC Installation Notes

HGLRC Forward F7 Dual Gyro FC Installation Notes

  • First, I had a really hard time dealing with the quad vibrating almost uncontrollably during the bench testing. I decided to activate Gyro #2 and this seemed to have fixed it although I don't know 100%. I can tell you that I ran a 4S lipo down to 9V (stupid I know) but the motors never got hot. This was a huge improvement from the last installation and test run. Here are some of the changes I made so far and then the "Dump All" File

Commands and Changes:

  • set gyro_to_use = second (this uses second gyro which in my case, seemed to correct the issue at this time)
  • I am going to keep adding to this so please stay tuned.
Radio Link AT9S Tight Sticks - Reduce Sensitivity from Cyclone FPV

Radio Link AT9S Tight Sticks - Reduce Sensitivity from Cyclone FPV

Radio Link AT9S Tight Sticks - Reduce Sensitivity from Cyclone FPV

Read more →

FireFly Camera Firmware Update Instructions from Cyclone FPV

FireFly Camera Firmware Update Instructions from Cyclone FPV

FireFly Camera Firmware Update Instructions from Cyclone FPV

Read more →

Connecting your HGLRC F3V4Pro to BetaFlight from Cyclone FPV Tutorials

Connecting your HGLRC F3V4Pro to BetaFlight from Cyclone FPV Tutorials

Connecting your HGLRC F3V4Pro to BetaFlight from Cyclone FPV Tutorials

Read more →

Setting Up Your ViFly Finder

Setting Up Your ViFly Finder

Use this video to help you setup the ViFly Finder 2 - I did the install on a Diatone build but the instructions can be used on any build.

Read more →

QX7 R9M/R9MM Updates

QX7 R9M/R9MM Updates

Watch the videos and follow along as you setup your QX7 with your R9M and R9MM / R9Mini Receiver from Cyclone FPV.

Read more →

Setting Up Taranis X9D+ TBS Crossfire / Nano and R9M/ R9MM

Setting Up Taranis X9D+ TBS Crossfire / Nano and R9M/ R9MM

Setting Up Taranis X9D+ TBS Crossfire / Nano and R9M/ R9MM

In an effort to help assist my customers with their new X9D+, I have created this video that details the proper steps to setup and update the firmware on your new Taranis X9D+ transmitter as well as how to setup the TBS Crossfire module and Nano Receiver. I have also added to this the entire setup details for the FrSky R9M and R9MM configuration to work with the X9D+. 

Read more →

Setting up X9D+ with OpenTX and Switches from Cyclone FPV

Setting up X9D+ with OpenTX and Switches from Cyclone FPV

Follow this video to setup your X9D+ with OpenTX and switches....

Read more →

Get RSSI to appear on OSD using Taranis transmitters from Cyclone FPV Tutorials

Get RSSI to appear on OSD using Taranis transmitters from Cyclone FPV Tutorials

Get RSSI to appear on OSD using Taranis transmitters from Cyclone FPV Tutorials

I have put some instructions here for people who are trying to get their RSSI to appear on their OSD. This is especially useful for those people that are using the R9Mini and R9MM as well as the XM series. While FrSky does have a firmware patch to push RSSI through channel 16, this is a manual way to assign it using your transmitter and BF settings. 

Read more →

ImmersionRC RapidFire Firmware Updates from Cyclone FPV Tutorials

ImmersionRC RapidFire Firmware Updates from Cyclone FPV Tutorials

Instructions on adding your firmware update to your Immersion RC Rapid Fire Module.

Read more →