RaceFlight Revolt F4 32KHz Flight Controller


$19.99 $39.99

Sorry, this item is out of stock

RaceFlight Revolt F4 32KHz Flight Controller from Cyclone FPV

The RaceFlight Revolt flight controller is the most advanced, performance driven, flight controller ever designed. Capable of running 32kHz gyro sample and PID loop, the Revolt is truly at the top of its class. The Revolt uses a F405 MPU and a super secret gyro (SSG) in combination with RaceFlight software to give you the BEST performance possible.

The Revolt presents not only the BEST performance, but also the most STABLE performance due to the amazing vibration rejection technology implemented in RaceFlight. Our filters allow your quad to stay in the air no matter what! Damaged propellers caused by that insane gate clip on turn 3? Not a problem. You can still finish the race!

In addition to the vibration rejection technology, the SSG gives you the highest speeds currently possible with the lowest noise floor and highest sensitivity. The SSG has never been used in any flight controller before and definitely gives you the leading advantage over others.

Simply install the Revolt onto your quad and get in the air right away – without the need for complicated tuning. The Revolt comes pre-configured with our latest official release of RaceFlight software for either FrSky or Spektrum (though it can be used on other receiver protocol brands as well). The solder pin layout is easy to read with motor connections in each corner. Just solder the closest motors and remember the order 1, 2, 3, 4.

Zadig and other complicated driver configuration tools are a thing of the past with the Revolt’s new driverless installation technology. Tired of messing around with Zadig or DFU to update your software? We were too, that’s why you no longer have to worry about messing around with them. The Revolt also features DFU free updating and a self-healing and updating bootloader, just in case something does go wrong.


  • LED Driver for WS2812b programmable LED
  • Infrared LED Race Transponder support – no need for separate transponder
  • SBUS Inversion
  • Future iPhone and Android configurator support
  • High Speed 32khz gyro, lowest noise floor and highest sensitivity gyro ever used
  • Through hole solder pads – forms an I-Beam when soldered for extra strength
  • FrSky Taranis, Spektrum, Futaba, JR, IBus, Sbus and other radio support
  • Integrated buzzer driver
  • Voltage and current ADC pins, for full voltage and current monitoring
  • Full telemetry output support
  • ESC flashing and configuration built into configurator
  • Most active software development
  • Selectable 3.3 voltage
  • 3 serial uarts
  • Bluetooth expandable
  • F4 processor
  • 16mb of flash memory
  • GPS expandable
  • Dimensions: 36mm x 36mm
  • Mounting holes: 30.5mm squared to center of holes

In addition to all the other amazing things the Revolt presents, customers who pre-order the Revolt get a special guarantee. When you adopt early within the first 72 hours, your Revolt will ship before any others! Revolters will also get access to RaceFlight’s ticketed tech support which will include step-by-step help with installation, tuning, and anything else that may arise with your Revolt.

Soldering the Revolt

The Revolt is very easy to solder and setup. The pin-through holes double as pads to easily solder wires to. Simply solder the closest corner pads labeled M1, M2, M3, or M4.

The Revolt requires a 5v BEC for power. The pads on the bottom of the board can be bridged for 5V or 3v3V to match the power requirement for your receiver.

If you are using the BB firmware, then make sure to put your inverted SBUS signal on TX1 and bridge the INV and TX1 pads. For everything else you can use TX3 for Spektrum, IBUS, etc.

If you are using RF1 firmware, you can solder any receiver to either TX1 or TX4 and choose whether or not the signal is inverted by bridging INV and TX or NOR (not inverted/normal) and TX.

The Revolt also has the ability to power an LED light and a buzzer. Simply follow the PINOUT diagrams below for a comprehensive look at how you can connect everything to the Revolt.

Customer Reviews

5 Based on 2 Reviews
5 ★
4 ★
3 ★
2 ★
1 ★
100reviewers would recommend this product Write a Review Ask a Question
  • Reviews
  • Questions

Thank you for submitting a review!

Your input is very much appreciated. Share it with your friends so they can enjoy it too!

Filter Reviews:
Ross p.
United States United States
I recommend this product

Great FC if you don't mind not having osd

Great FC still I don't mind not having the osd plus you can now run falco x on it

william h.
United States United States
I recommend this product


Love this fc simply the easiest to use and set up,and the performance is #1solid as always taerk hooks up all the good stuff you a great price .This is my go to vendor for sure!!!

Facebook retargeting pixel