JHEMCU F4 2-6S Flight Controller AIO OSD BEC

JHEMCU

$23.99 

JHEMCU F4 2-6S Flight Controller AIO OSD BEC from Cyclone FPV

Connects via cable to JHEMCU 55A 4-in-1 ESC

Specification:

  • Brand Name: JHEMCU
  • Item Name: Betaflight F4 OSD Flight Controller Integrated with BEC Output
  • MCU:  STM32F405RGT6
  • Gyroscope: MPU6000
  • Barometer: NO  ( Reserved pad)
  • Input Voltage: 2-6S Lipo
  • BEC 1 Output: 5V @ 2A ( for LED/ Receiver/ Buzzer etc.) 
  • BEC 2 Output: 8V @ 3A ( for VTX / Camera)
  • Integrated with OSD (AT7456E) , support BF Ground Station adjust OSD
  • Black box: TF Card Holder 
  • Receiver: Support PPM, SBUS, IBUS, DSM2/ DSMX Receiver
  • Size: 36x36mm
  • Mounting Hole: 30.5x30.5mm, M4
  • Weight: 6.9g
Instruction for diagram picture:
  • +5V:  BEC 5V 2A con.  ( 2.5A Max.)
  • 3.3V: LDO3.3V    ( 300mA Max.)
  • VBAT+: share Lipo power
  • CUR: ESC Current signal input
  • S1, S2, S3, S4, S5, S6: ESC Signal
  • VTX: Video output for video Transmitter
  • VIN: Camera Video input
  • 8V: Con. Current 3A  ( for VTX and Camera Power supply)
  • BZ- : General active 5V buzzer for dbuz 5V
  • RSSI: Receiver RSSI INPUT
  • LED: WS2812 LED signal
  • SCL & SDA: I2C_SCL & I2C_SDA
  • PPM: PPM RC Receiver Input
  • SBUS: SBUS RC Receiver Input
  • D/I: DSM and IBUS RC Receiver Input
  • (RC Receiver,SBUS,IBUS,DSM: RX1 )
  • T1: UART1 TX1  
  • R3 & T3: UART3 RX3 and TX3
  • R6 & T6: UART6 RX6 and TX6
Package Included:
  • 1x F4 Flight Controller Board
  • 4x M3 Anti-vibration Balls
  • SBUS will be on UART1
  • SPort will be on UART3 (bottom of board)
Customer Reviews
2.0 Based on 1 Reviews
Write a Review Ask a Question
  • Reviews
  • Questions

Thank you for submitting a review!

Your input is very much appreciated. Share it with your friends so they can enjoy it too!

Filter Reviews:
  • handling
  • resources
  • pads
  • soldering
  • board
  • Thought
CS
06/20/2020
carl s.
United States United States
I recommend this product
JHEMCU F4 2-6S

Thought i would try a new inexpensive FC. My bad. Dont get me wrong I have not flown it yet. But was/am disappointed that 2 of the solder pads came right off the board after soldering. This is one of many boards I have built, so it was not caused by my handling. I was able to move around some resources and will be able to use the board. As long as no other pads come loose.

06/30/2020
CycloneFPV.com

Carl, In the future, if you happen to experience an issue that you believe is created from a defective product, please use our online RMA contact form here and we can help to issue an RMA and replace your item. https://www.cyclonefpv.com/pages/contact

Facebook retargeting pixel