HappyModel Mobula6 FlySky FrSky Versions

HappyModel Mobula6 FlySky FrSky Versions from Cyclone FPV

Specification:

• Brand Name: Happymodel
• Model: Mobula6
• Item Name: 65mm Crazybee F4 Lite 1S Brushless Whoop FPV Racing Drone BNF
• Optional Version: Frsky Receiver ( Compatible with ACCST D8/D16, Recommend D8 mode)
• Flysky Receiver ( Compatible with AFHDS and AFHDS-2A Flysky transmitter)
• Drone Wheelbase: 65mm
• Size: 80x80x37mm
• Weight: 20g

Crazybee F4 LiteFlight Controller:

• Built-in ESC & Receiver & VTX
• Frsky SPI RX version) CRAZYBEE F4 Lite Frsky version Firmware target: CrazybeeF4FR
• (Flysky SPI RX version) CRAZYBEE F4 Lite Flysky version Firmware target: CrazybeeF4FS
• MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
• Sensor: MPU-6000(SPI connection)
• Board size: 28.5 * 28.5MM
• Power supply: 1S battery input (DC 2.9V-4.35V)
• Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
• Built-in Betaflight OSD(SPI Control)
• Built-in 5.8G VTX
• Built-in SPI Frsky/Flysky receiver
• Built-in 5V 1A BEC
• Built-in voltage detection

 Onboard Frsky Receiver Version:

• SPI BUS receiver Frsky D8 compatible
• Compatible Non-EU transmitter D8 model
• - Frsky_x_lbt Support EU LBT Radio Transmitter
• Channels: 8ch
• Failsafe support
• No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m

Onboard Flysky Receiver Version:

• SPI BUS receiver
• Protocol: AFHDS and AFHDS-2A Switchable
• Channels: 8ch(AFHDS) or 14ch(AFHDS-2A)
• No ground interference ( Transmitter and receiver 1 m from the ground): 100~200m
• Failsafe support

Onboard 5A BLheli_S 4in1 ESC:

• MCU upgraded to EFM8BB21
• Power supply: 1S LiPo/LiPo HV
• Current: 5A continuous peak 6A (3 seconds)
• Support BLHeliSuite programmable
• Factory firmware: O_H_5_REV16_7.HEX
• Default protocol: DSHOT600

• Model: SE0802
• KV: 19000KV / 25000KV Motor
• Configuration:9N12P
• Stator Diameter:8mm
• Stator Length:2mm
• Shaft Diameter:1mm
• Motor Dimension(Dia.*Len):10.5mm*14.9mm
• Weight(g):1.9g
• No.of Cells(Lipo):1S only

Gemfan 1219 3-Blade Propeller:

• Brand Name: Gemfan
• Center Thickness:5mm
• Prop Disk Diameter:31mm
• Center Hole Inner diameter:1.0mm
• Quantity: 4 CW & 4 CCW
• Weight:0.28g

Onboard 5.8G 40CH 25mW VTX Output power: 25mw

• Frequency: 40CH
• Input voltage: 3.3V 5.5V
• Current consumption: 300mA(type)
• Frequency: 5.8GHz 5bands 40 channels
• With Race band
• Smart audio ready

Runcam Nano 3 FPV Camera Brand Name: Runcam

• Model: Nano 3
• Item Name: 1/3 CMOS 800TVL Camera
• Electronic Shutter Speed: Auto
• Auto Gain Control (AGC): Auto
• Min. Illumination: 0.01Lux@1.2F
• D-WDR: Auto
• Day/Night: Color
• Power: DC 3-5.5V
• Current: 110mA@5V 120mA@3.3V
• Housing Material: ABS
• Net Weight: 1.2g
• Dimensions: L14mm*W14mm*H9mm

Lipo Battery ( Included):

• Continuous Discharge Rate: 30C
• Size: 57mmx12mmx7mm
• Weight: 8g
• Connector: PH2.0
• Quantity: 4 PCS

Package Included:

• 1x Mobula6 1S FPV Racing Drone
• 3x 1S 300mAh 30C Lipo Battery
• 1x 1S Lipo/LIHV USB Charger
• 1x Propeller disassemble Tool

Here is the VTX Table that was used in our videos below. Please make sure to right click on the file and then left click on save file as or save target as. Do not just click on it or else it will open and not download.